Accessories & Tools

These APC 4D 3D Slow Fly props are the solution to a light weight yet rigid prop ideal for fast reverse rotatinal direction for the hard core 3d/4D pilot.  We've tested these props with our 18A...

These APC 4D 3D Slow Fly props are the solution to a light weight yet rigid prop ideal for fast reverse rotatinal direction for the hard core 3d/4D pilot.  We've tested these props with our 18A...

Not your ordinary over-the-counter O-ring, great replacement 3/32" thick standard bands ideal for running stock setup systems running 2s! Great replacements for our 14-30g out-runner prop savers...

Not your ordinary over-the-counter O-ring, heavy duty 1/8" thick ideal for running 3s setups! Great replacements for our 24-30g out-runner prop savers o-rings. These o-rings were made to handle all...

The ultimate solution for an ultra light weight nose cone for our small prop saver style motors.   Not only do these look good, but can provide even greater durability to your EPP model by preventing...

The ultimate solution for an ultra light weight nose cone for our small prop saver style motors.   Not only do these look good, but can provide even greater durability to your EPP model by preventing...

Keep things looking sharp, light and your electronics cooler with these hollowed spinner.   These 51mm Air-Flow spinners have a backplate that is 51mm (2 inches) in diameter with an overall length of...

Keep things looking sharp, light and your electronics cooler with these hollowed spinner.   These 51mm Air-Flow spinners have a backplate that is 51mm (2 inches) in diameter with an overall length of...

These are the direct replacement Collect/Prop Adapter 4mm shaft out runner motors Hub (motor shaft) diameter = 4mm

Prop-Saver Band Installation Tool This compact hand tool makes it easier to install and remove prop-saver bands

Twisted Hobbys Control Throw Angle-Meter Tool The Twisted Hobbys Control Throw Angle-Meter provides a simple an

Twisted Hooker Aircraft Mounting Kit The Twisted Hooker provides a simple way to store RC aircraft overhead and

Control Throw Dangle-O-Meter Tool The Twisted Hobbys Dangle-O-Meter provides an easy and accurate way to measur

Ultra Halo XX0 LED Light Stick Kit: Small and Lightweight The Ultra Halo XX0 is our smallest and lightest LED l

Finally an accurate way to set center of gravity on your favorite Twisted Hobbys EPP Foamie.  CG machine comes unassemblied with protective tape which can be removed before assembly.  * If stan

Ultra Halo XX1 LED Light Stick Kit: Large The Ultra Halo XX1 is a lightweight, high-output LED lighting kit des

Best way to never forgot your CG locations!  Easy to peal and stick on your model.  Kit includes 4 cg stickers. 

Another great tool for easy caring, Twisted Hobbys new reference card allows for quick measurments.   Made from Alum and includes a plastic protective pouch.    

Finally an accurate way to see if your building our favorite Twisted Hobbys EPP Foamie square and true.  Measures 3" on each side, comes with protective tape over square.  

Simply yet must have item for your foamies at home or at the field!  One of the biggest power loss issues is an out of balanced prop! High Sensitivity Propeller Balancer, will work with all of our...

20 pc's plastic wire staples, great product for holding down wires for electronics, also used for LED kits.

Used for holding batteries, receivers, esc's or other components down.  Great addition for modeling. Includes: 2 pc (Male & Female) : Black 1" x 4" Velcro Hook & Loop sticky back

Used for holding batteries or other components down.  Great addition tool for modeling. Includes: 1 pc : 1/2 x 5 1/2 Velcro Strap

Design for the 30-32" EPP models and or any other foamie 5oz -11oz. Ideal for a light weigh indoor

Design for the 30-32" RcFactory/Hacker and any other foamie 5oz -11oz. Ideal for indoor/outdoor use. Each kit contains a set of lightweight carbon-fiber landing gear, g10 fuselage supports, g10 spats...

Rc Factory landing gear 1 piece.  Used for any of the Rc Factory 37-39" Mono models.  

Rc Factory landing gear 1 piece.     Includes:  One piece carbon fiber landing gear.

Rc Factory landing gear 1 piece.     Includes:  One piece carbon fiber landing gear.

Rc Factory landing gear 1 piece.  Used for any of the Rc Factory Crack Pitts XL and Air Truck models.    Includes:&nbs

Rc Factory 40-43" models with Version 2 landing gear assemble, this is for all newer revised landing gears.  Include a 1 piece carbon fiber landing gear set. 

Rc Factory 40-43" Replacement Carbon-Fiber Landing Gear Version 1, this was from the original design, no longer in production.    Include a 1 piece carbon fiber landing gear set.  

Rc Factory 40-43" Replacement landing gear straps.  Designed to work for with "Version 1"  42-43" Mono Series Models Version, not to be used with Version 2 landing gear/models.

Rc Factory 40-43" Replacement landing gear straps.  Designed to work for with "Version 2"  40-43" Series Models Version 2, not to be used with Version 1 landing gear/models.  This is shorter in...

Twisted Hobbys HD Tail Wheel Assembly Kit, used for 36-48" models.  Removes all worries for wearing down hard stock or EPP tail wing.  Durable and easy to assembly as well as install.   Total weight...

Bush Landing Gear Suspension Kit Designed by Twisted Hobbys, the Bush Landing Gear Suspension Kit creates a fun

Are you looking for and off road solution to tax, take off and land in deeper grass?  We have the solution!   These training wheel kits are huge, durable and light weight, also a direct replacement...

The new transparent iron-on film with enhanced adhesion, which can be applied directly to EPP, is now available. It tolerates a wide range of temperatures on a typical modeling iron, but we advise...

The new transparent iron-on film with enhanced adhesion, which can be applied directly to EPP, is now available. It tolerates a wide range of temperatures on a typical modeling iron, but we advise...